Bore and Stroke Correct, and the Cylinder Still Will Not Fit

Pneumatic cylinder bore and stroke - dimension guide

Replacing a cylinder sounds simple: give the bore, give the stroke. But sometimes both numbers are right, and the new unit still will not go in - the mounting holes do not line up, the rod end will not connect, or the body will not fit in the space.

The reason is that bore and stroke describe the internal dimensions and the travel distance - not the external identity of the whole cylinder.

The same bore and stroke does not mean the same body length, the same mounting hole spacing, or the same rod thread. Separate the two dimensions properly and the rest of the selection stops getting confusing.

Bore is not how thick the body is

This article concerns the common round-body, single-rod, double-acting cylinder.

Bore is the internal diameter of the barrel - the circle in which the piston travels. It is not the outside diameter of the barrel, and certainly not the rod diameter.

Some cylinders have a square body, some round, and there may be tie rods or sensor grooves outside. Clamping a caliper on the outside of the body does not give you the bore.

If you cannot see inside, read the complete model number on the nameplate and check the catalogue for that brand and series. Do not dismantle a cylinder that is still on the machine just to confirm the bore.

Bore determines the piston's effective area. In an ideal comparison at equal pressure and otherwise identical conditions, a larger effective area gives greater theoretical thrust. But the load it can actually move also depends on friction, exhaust-side pressure and operating conditions - theoretical output alone is not a basis for selecting at full capacity.

Stroke is not the length of rod sticking out

Stroke is the distance the piston travels from one end position to the other. With an ordinary fixed rod connection, the rod end moves the same distance.

Suppose the rod end already protrudes when the cylinder is fully retracted, and protrudes further when fully extended. The difference between the two positions is the stroke - not the total exposed length when extended.

Measuring the overall body length includes the end caps. Measuring only the exposed rod may include the portion that was already exposed when retracted. Both methods are easy to get wrong.

Safety: do not measure stroke by pushing a pressurised cylinder by hand, briefly applying air, or forcing the machine load. Use the model number and drawings first. Where measurement is required, qualified personnel should isolate the energy source, release residual pressure and support the load per the equipment procedure. Position confirmation and test running must be carried out under controlled conditions.

Reading the two numbers from the model code

Taking the ordering rule for the AirTAC SAU series catalogue as an example: the first size figure is the bore, the second is the stroke.

Under that rule, the size segment "50x100" means bore 50 mm, stroke 100 mm. It does not mean a 50 mm outside diameter, a 100 mm overall length, or a 50 mm rod.

That is only the interpretation of the size segment - not complete ordering information. Magnet, mounting type, seal material and thread are covered by other codes. For another brand or series the naming rule must be checked again; it cannot simply be carried over.

Both numbers right - what else has to be confirmed?

Mounting. The existing hole spacing, fixing method and available space determine whether the new cylinder can physically go in. Matching bore and stroke is not enough to confirm drop-in replacement.

Rod end connection. Is the rod driving a fixture, a pusher plate or something else? If the rod thread or connection dimensions do not match, correct size figures still will not connect.

Ports and sensing. Check port size and orientation, whether the machine needs magnetic switches, and whether the new cylinder is magnetic and can work with the existing mounting arrangement.

Action requirements. Is it pushing on extension or pulling on retraction? Is there side load, and what are the speed and cushioning requirements? A "50x100" does not answer any of that. On an ordinary single-rod double-acting cylinder the effective areas differ between the two sides, so theoretical extend and retract forces cannot be treated as equal.

When purchasing, the easiest route is not two numbers but the complete nameplate, the mounting position and a photo of the rod end, confirmed against the dimensional drawing.

Bore is the internal diameter, stroke is the travel distance. To replace directly, you still need the full model number and the mounting dimensions.

Reference

AirTAC SAU/SAUF official catalogue - bore, theoretical output, stroke and ordering code (pp.63-64). The series is used here only to explain the coding and does not imply direct interchangeability. Festo cylinder product information - cylinder types and accessory classification. Dimensions shown are illustrative and not to scale; ordering and installation follow the drawing for the specific model.


Frequently asked questions

Bore and stroke match but it will not fit. Why?

Because bore and stroke are internal dimensions. Body length, mounting hole spacing, rod thread, port position and switch compatibility are separate and must be confirmed from the model number and drawing.

Is bore the outside diameter of the cylinder body?

No. Bore is the internal diameter of the barrel in which the piston travels. The outside of the body can be square or round and is not a measure of bore.

How do I measure stroke correctly?

Stroke is the travel between the two end positions - the difference between the rod end position fully retracted and fully extended, not the total exposed rod length. Use the model number and drawing where possible.

What does "50x100" mean in a cylinder model code?

In the AirTAC SAU series it means bore 50 mm and stroke 100 mm. Other brands and series use different rules, so confirm the catalogue for the specific series.

What should I send to a supplier for a replacement cylinder?

The complete nameplate, mounting position photos, rod end photos, and the action requirements (push or pull, side load, speed, cushioning). That avoids most replacement errors.

Pneumatic components

elechub.ls supplies pneumatic push-in fittings, tubing, valves, silencers and cylinders - sourced factory-direct from Liushi, China and inspected before dispatch.

Need a second price on pneumatic components? Send us the part numbers. Request a quote.


Related reading