A cylinder that moves badly is easy to misdiagnose. Sticking at the same position every stroke, juddering the whole way, and hesitating before it lurches are three different symptoms - and they usually have three different causes. Turning up the regulator first is the wrong move.
Separate the symptom, then look for the cause.
1. It sticks at the same position every time
Look at the barrel first. If the cylinder has been knocked or clamped and the bore is deformed, the piston meets extra resistance at that one point. The signature is distinctive: not slow throughout, but rough at the same spot on every stroke.
Check for impact marks or clamp marks on the outside, and ask whether the cylinder was moved or re-mounted shortly before the fault appeared. Absence of visible damage does not rule out an internal problem.
A fixed sticking point is not always the barrel. A bent piston rod, or a pusher plate, fixture, slide or guideway binding at one point, produces a similar pattern. So inspect what the cylinder drives, not only the cylinder. Do not raise the pressure to force it through the obstruction.
2. It judders the whole way, and will not run slowly
Two things to check: whether the air supply is adequate during motion, and whether the speed controller is closed too far.
A cylinder moves on the net force from the pressure difference across the piston, working against load and friction. If the force margin is thin, or the speed controller is nearly shut, the sequence becomes: air enters, pressure builds, force becomes sufficient, the piston moves, conditions change, the piston stops, then starts again. You see stop-start motion rather than a slow, continuous stroke.
This is why a standard cylinder cannot be slowed to any arbitrary speed simply by closing the speed controller further. Low-speed operation has a practical limit, and beyond it more throttling does not produce stable motion.
Check the supply during the stroke, not only with the machine idle. Look at whether the speed controller is set too small, whether tubing is kinked or pinched, and whether the requested speed is inside the range for that model. And do not open the controller fully in one movement - a cylinder that was juddering can turn into one that moves dangerously fast.
3. It hesitates, then lurches away
Distinguish two cases: does it stall and then move, or is it specifically the first stroke after the machine is re-pressurised?
Stalls, then moves. Breakaway friction at start-up may exceed the available force. Pressure builds until the piston finally breaks free; once moving, running friction is lower, so the cylinder accelerates suddenly. Restricted supply, poor alignment and abnormal friction should all be examined along that sequence - "restricted flow" is not a sufficient explanation on its own.
First stroke after re-pressurising is fast. In a meter-out circuit, speed is controlled by restricting the exhaust. If the exhaust side has not yet built up back pressure at start-up, the first stroke behaves differently from normal running. Back pressure here means the opposing pressure the exhaust side presents to piston movement.
These two cases both look like sudden acceleration, but they are not solved the same way. Recording whether the fault only appears after re-pressurising is more useful than repeatedly adjusting the speed controller.
4. It reaches the end, but will not return
If the cylinder extends but will not retract, or the reverse, do not check only whether the directional valve has actually shifted. Check whether the side that should be exhausting can actually exhaust.
A double-acting cylinder does not change direction by supplying air to the other side alone - the opposite chamber must also vent. If the exhaust path is blocked, trapped air forms a counter-force, and the cylinder may move sluggishly or not at all even with the other side pressurised.
Follow the exhaust path: kinked tubing, a speed controller closed or connected the wrong way round, the valve exhaust port, and the silencer. But "will not return" is not proof of a blocked exhaust - incorrect supply switching and external jamming can also hold a cylinder at the end of stroke.
Safety: never disconnect a fitting under pressure to test the exhaust. Isolate and lock out the energy source, release and verify residual pressure, and support any load that could fall or move, before work is carried out by a competent person.
Describing the fault properly
When you ask someone for help, replace "the cylinder is not working well" with a specific description: sticking at a fixed position, juddering throughout, lurching on re-pressurisation, or failing to return from the end of stroke?
Reference
SMC - Basic Pneumatic Circuit Fault Checklist and Fault Check Points. The barrel-dent diagnosis line is based on field experience and is not a ranking of failure probability. Inspection and adjustment should follow the manual for the specific model and the equipment safety procedure.
Frequently asked questions
Why does my cylinder stick at the same position every stroke?
Most often a deformed or scored barrel bore at that point, a bent piston rod, or a guideway or fixture binding there. It is a positional problem, not a general speed problem, so raising the regulator will not fix it and may cause damage.
Why does the cylinder judder when I try to run it slowly?
Usually the speed controller is closed too far, so the force margin becomes marginal and the piston moves in stop-start steps. A standard cylinder has a practical minimum stable speed; beyond it, further throttling makes motion worse, not better.
Why is the first stroke after re-pressurising faster than the rest?
In a meter-out circuit the exhaust side needs back pressure to control speed. At start-up that back pressure has not yet developed, so the first stroke runs faster. Check the circuit configuration and the start-up sequence.
The cylinder reaches the end but will not return. Why?
Check the exhaust path, not only the valve. A double-acting cylinder needs the opposite chamber to vent; blocked tubing, a closed or incorrectly fitted speed controller, or a blocked silencer will hold it. External jamming and incorrect valve switching can look the same.
Can I just increase the air pressure to push through a sticking point?
No. It masks the symptom, raises stress on the whole circuit, and can cause sudden uncontrolled movement once the obstruction releases. Find and correct the mechanical cause first.
Components in pneumatic circuits
elechub.ls supplies the pneumatic components involved in these circuits - push-in fittings, tubing, speed controllers and silencers - sourced factory-direct from Liushi, China and inspected before dispatch.
- Pneumatic push-in fittings - straight, elbow, tee, Y and cross types
- Request a quotation for speed controllers and silencers
Need a second price on pneumatic components? Send us the part numbers. Request a quote.
One more reason to fix it properly
Compressed air is one of the most costly utilities on a shop floor. A cylinder that judders because the speed controller is throttled too far is not only unreliable - it is usually running at a setting that wastes air to compensate for a force margin that was never adequate.
Correcting the underlying restriction is normally both a reliability fix and an energy fix. Turning the regulator up to force the movement through is neither.